联系人:魏经理
电话:15165311861
手机:15165311861 15853170198
地址:济南市标山南路绿地东门
当前位置:首页-最新公告最新公告
玻璃门安装流程!安装标准是啥?
作者:山东玻璃门 来源:http://www.jnkdblgd.com/ 发布时间:2017-10-03 19:45:46 浏览次数:647
玻璃门是比较特殊的一种门扇,首先它的厚度不足以说是一种实心门,而它又不属于异型门,事实上,它是一种特殊形式的门扇。玻璃门的特征是由玻璃本身的特征决定的。
Glass door is a special kind of door leaf. First of all, its thickness is not enough to say that it is a kind of solid door, and it is not a special-shaped door, in fact, it is a special form of door leaf. The characteristics of the glass door are determined by the characteristics of the glass itself.
玻璃门安装施工工艺标准?
Glass door installation process standards?
A、、材料要求
A, material requirements
1、玻璃门的型号规格应符合设计要求,五金配件配套齐全,并有出厂合格证。
1, glass door model specifications should meet the design requirements, hardware fittings complete, and factory certification.
2、固定玻璃板必须和玻璃门厚度相同,且必须符合设计要求,有出厂合格证。
2. The fixed glass plate must be the same thickness as the glass door, and must comply with the design requirements and have the factory certificate.
3、辅助材料、密封胶、万能胶等应符合设计要求和有关标准规定。
3, auxiliary material, sealant, and so on should comply with the design requirements and the relevant standards.
B.作业条件
B. operating conditions
1、墙、地面的饰面已施工完毕,现场已清理干净,并经验收合格。
1, wall, ground finishes have been completed, the scene has been cleaned and accepted.
2、门框的不锈钢或其它饰面已完成,门框顶部用来安装固定玻璃板的限位槽已预留好。
2, the door frame of stainless steel or other finishes have been completed, the top of the doorframe to install fixed glass plate of the limit slot has been reserved.
3、把安装固定厚玻璃的木底托用钉子或万能胶固定在地面上,接着在木底托上方中引一侧钉上用来固定玻璃板的木条,然后用万能胶将该侧不锈钢或其它饰面粘在木底托上,铝合金方管可用木螺丝固定在埋入地面下的防腐木砖上。
3, the installation of fixed thick glass wood base is fixed on the ground with a nail or adhesive, then in the wood base above cited in the side nail for fixing glass plate strips, and then use the adhesive to the side of stainless steel or other decorative glued wood base, Aluminum Alloy square available wood screws in the buried ground anticorrosive wood block under the.
4、把开闭活动门扇用的地弹簧和定位销按设计要求安装在地面预留位置和门框的横梁上。
4. The ground spring and the locating pin for the door opening and closing movable doors shall be installed on the floor reserved position and the crossbeam of the doorframe according to the design requirements.
5、从固定玻璃板的安装位置的上部、中部和下部量三个尺寸,以最小尺寸为玻璃板的裁切尺寸。如果上、中、下量得的尺寸一样,则裁玻璃时其裁切宽度应小于实测尺寸2mm,高度应小于实测尺寸4mm.玻璃板裁好后,应在周边进行倒角处理,倒角宽度2mm.
5, from the fixed glass plate installation position of the upper, middle and lower three sizes, with minimum size for the glass plate cutting size. If, the size, cut glass when the cutting width should be less than the measured size 2mm, height should be less than the measured size of 4mm. glass plate cut, should be in the surrounding of chamfer, fillet width 2mm.
C.施工操作工艺
C. construction operation process
1、固定玻璃的安装:
1. Installation of fixed glass:
(1)、用玻璃吸盘器把裁切好、倒好角的玻璃吸紧,然后手握吸盘器把玻璃板抬起,插入门框顶部的限位槽内后放到底托上,并调整好安装位置,使玻璃板边部正好盖住门框立柱的不锈钢或其它饰面的对口缝,接着在木底托上钉另一侧木条,把玻璃板固定在木底托上。在木条上涂刷万能胶,将该侧不锈钢饰面或其它饰面粘卡在木方上。
(1), with a glass sucker to cut back, corner of the glass ceiling tight, then holding a sucker to the glass plate is lifted, a limiting groove is inserted into the door frame at the top of the post on the bottom support, and adjust the installation position of the glass plate edge covers frame column or other decorative stainless steel then the other side of the nail to sew, wood in wood base, the glass plate is fixed on the wood base. Paint on wood adhesive, the side of stainless steel or other decorative veneer sticking in the wood on the side.
(2)、在门框顶部限位槽处和底托固定处、玻璃板与门框立柱接缝处注入密封胶。注胶时紧握注射枪压柄的手用力要均匀,从缝隙的端头开始,顺着缝隙均匀缓缓移动,使密封胶在缝隙处形成一条表面均匀的直线,最后用塑料片刮去多余的密封胶,并用干净抹布擦去胶痕。
(2) at the limit slot at the top of the doorframe and the fixing place at the bottom support, the sealant is inserted into the joint between the glass plate and the doorframe post. When the glue gun handle hand hold pressure force should be uniform, starting from the end of the gap, the gap along the uniform moving slowly, the sealant to form a uniform surface line at the gap, at last with a plastic film to scrape off the excess sealant, and glue mark with clean dishcloth.
2、上固定玻璃板必须用两块或多块来对接,对接时对接缝应留2∽3mm、的距离,玻璃的边必须倒角,对接的玻璃定位并固定后,用注射枪将密封胶注入缝隙中,注满后用塑料片在玻璃两侧刮平密封胶,用干净布擦去胶迹。
2, fixed on the glass plate must be docking of two or more, should be 2 ~ 3mm, the distance of the seam butt, glass edge must be chamfered, positioning and fixing the glass butt after injection gun sealant into the gap, is filled with a plastic film on the glass on both sides scraping seal glue, with a clean cloth to wipe glue.
3、活动门扇的安装
3. Installation of movable door leaf
4、用吊线坠测量地弹簧与门框横梁上定位销中心是否在同一直线上,若不在同一直线上,必须及时处理使用使其同轴线。
4, with a plumb line to measure the spring and frame the beam center is in the same line, if not in the same line, must be timely treatment to the same axis.
5、在门框的上下横档内画线,并依线和地弹簧安装说明书固定转动销的销孔板及地弹簧的转动轴联接板。
5, in the frame on the bottom rail lines are drawn, and according to the line and the spring installed rotating shaft connecting plate fixed rotation pin hole plate and pin spring specification.
以上文章来源于山东玻璃门http://www.jnkdblgd.com/