联系人:魏经理
电话:15165311861
手机:15165311861 15853170198
地址:济南市标山南路绿地东门
当前位置:首页-行业动态行业动态
玻璃门的安装流程
作者:admin 来源:本站 发布时间:2018-05-11 11:33:23 浏览次数:561
    玻璃门具有别样的好处,可以增加空间感,采用磨砂玻璃时,门就具有隐私性;采用钢化透明玻璃,门扇就具有通透功能。当你的新房已经修葺好了,准备进行玻璃门的安装时候,有没有担心过安装师傅的差错让你漂亮的门美中不足呢?那么下面我们就一起来看看玻璃门的安装流程:
    The characteristics of the glass door are determined by the characteristics of the glass itself. When the glass is used, the door has the privacy of the door, and the door fan is permeable with the transparent glass. When your new house has been repaired and ready for the installation of glass doors, have you ever worried about the mistake of installing the master to make your beautiful door a perfect flaw? Now let's take a look at the installation process of the glass door.
    1、由固定玻璃和活动玻璃门扇组合在的玻璃门,统一进行放线定位。

    The glass doors combined with fixed glass and movable glass doors shall be uniformly positioned for positioning.

济南凯达玻璃隔断

    2、限位槽的宽应大于玻璃厚度2-4mm,槽深为10-20mm。安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。
    the width of the limiting slot should be greater than the glass thickness 2-4mm and the groove depth is 10-20mm. When installing, the two metal decorative panel sidelines are drawn from the middle line of the projectile, and then the installation of the limiting slot on the top of the doorframe is carried out according to the sideline.
    3、先把方木固定在地面上,然后再用万能胶将金属饰面板粘在木上,方木可采用直接钉在预埋木砖上,或通过膨胀螺栓连接的方法固定。
    first the wood is fixed on the ground, and then the metal panel is glued to the wood with all energy glue. The square wood can be directly nailed on the pre embedded wood brick or fixed by the method of expansion bolt connection.
    4、接所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形和位置,最后外包金属装饰面。
    pick up the center line and nail the door frame, then use plywood to determine the shape and position of the door frame column, and finally wrap the metal decorative surface.
    5、用玻璃吸盘机把厚玻璃吸紧,然后手握吸盘把由2-3人将厚玻璃板抬起,移至安装位置。
    use glass suction machine to tighten thick glass, then hold the suction cup to lift the thick glass plate from 2-3 people to the installation position.
    6、在底托方木上的内外钉两根小方木条把厚玻璃夹在中门,方木条距玻璃板面4mm左右,然后在方木条上涂刷万能胶,将饰面金属粘卡在方木条上。
    the inner and outer nail on the bottom of the tree is sandwiched with thick glass in the middle door, the square wood strip is about 4mm from the glass plate, and then the square wood strips are painted with all energy glue, and the veneer metal is stuck on the square wood bar.
    7、在顶部限位槽和底部托槽口的两侧,以及厚玻璃与框柱的对缝处等各缝隙处,注入玻璃胶封口。
    at the top limit groove and the bottom bracket mouth on both sides, as well as thick glass and frame column of the joint and other gaps, filling glass glue seal.
    8、玻璃门固定部分因尺寸过大而需要拼接玻璃时,其对缝要有2-3mm的宽度,玻璃板边要进行倒角处理。
    the glass door fixed parts because of the size is too large and need to stitching glass, its seam should have 2-3mm width, glass plate edge should be chamfered.
    9、门扇安装前,地面地弹簧与门框顶面的定位销应定位安装完毕,两者必须同轴线,安装时用吊垂线检查,确保地弹簧转轴与定位销的中心线在同一会直线上。
    Before the door fan is installed, the positioning pin of the ground spring and the top of the door frame should be fixed and installed. Both must be coaxial, and the vertical line is checked with the hanging line when installation, so as to ensure the line of the earth spring shaft and the center line of the positioning pin in the same line.
    10、把上下金属门夹分别装在玻璃门扇上下两端,并测量门扇高度。
    Install the upper and lower metal door clamps on the upper and lower ends of the glass door leaf, and measure the height of the door leaf.
    本文由济南凯达玻璃隔断有限公司友情奉献,更多有关的知识请点击http://www.jnkdblgd.com/。我们将用最先进的技术,最真诚的态度,为您提供最为全面的服务。