Now when it comes to partition door, we will first think of glass partition door, not only because it looks beautiful, but also because it is very practical, which can increase a sense of visual magnification of space, and it is also a choice with high cost performance.

玻璃移门由于其安装方便，开启灵活，节省空间等优点，现在很多家庭、办公、娱乐场所都大量应用，成为必不可少的装修材料。在我们选购客厅隔断玻璃移门的时候会很迷茫，尽管如此在挑选时我们一定不能随意的选购一个糊弄了之，所以炫威小编提醒您，在选购玻璃移门的时候，一定要先掌握一定的相关知识：

Glass sliding door is widely used in many families, offices and entertainment places because of its advantages of convenient installation, flexible opening and space saving. We will be confused when we choose the living room partition glass sliding door. However, we must not choose one to fool it at will, so Xuanwei Xiaobian reminds you that when we choose the glass sliding door, we must first master some relevant knowledge:

玻璃门厂家在安装隔断玻璃门是应注意：

The glass door manufacturer shall pay attention to the following when installing partition glass doors:

1、玻璃与基架不锈钢框的结合不能太紧密，玻璃放入不锈钢框后，在不锈钢框的上部和侧边应留有3毫米左右的缝隙，该缝隙是为玻璃热胀冷缩准备的。

1. The combination of glass and base frame stainless steel frame shall not be too close. After the glass is put into the stainless steel frame, a gap of about 3mm shall be left on the upper and side of the stainless steel frame, which is prepared for glass thermal expansion and cold contraction.

2、安装玻璃隔断门之前，要检查玻璃的角是否方正，检查不锈钢框的尺寸是否正确，有否走形现象。在校正好的不锈钢框内，定出玻璃安装的位置线，并固定好玻璃板靠位线条。

2. Before installing the glass partition door, check whether the corner of the glass is square, whether the size of the stainless steel frame is correct and whether there is deformation. Set the position line of glass installation in the right stainless steel frame, and fix the position line of glass plate.

3、在安装玻璃隔断门时，用玻璃吸盘机把厚玻璃吸紧，然后手握吸盘把由2-3人将厚玻璃板抬起，移安装位置。然后玻璃上部插入门框顶部的限位槽，把玻璃的下部放在底托上，玻璃下部对准中心线，两侧边部正好封住门框处的金属饰面对缝口，要求做到内外都看不见饰面接过口。

3. When installing the glass partition door, use the glass suction cup machine to suck the thick glass tightly, then hold the suction cup and lift the thick glass plate by 2-3 people to the installation position. Then insert the upper part of the glass into the limit slot at the top of the door frame, place the lower part of the glass on the bottom support, align the lower part of the glass with the center line, and the edges on both sides just seal the metal facing butt joint at the door frame. It is required that the facing joint can not be seen inside and outside.

4、再给玻璃隔断门注口封胶时，要在顶部限位槽和底部底托槽口的两侧，以及厚玻璃与框柱的对缝处等各缝隙处，注入玻璃胶封口注胶时，由需要注胶的缝隙端头开始，顺缝隙均匀灌注，使玻璃胶在缝隙处形成一条表面均匀的直线，用塑料片刮去多余的玻璃胶，并用布擦净胶迹。

4. When sealing the injection opening of glass partition door, glass glue shall be injected at both sides of the top limit slot and the bottom bottom support slot, as well as at the butt joint between thick glass and frame column. When sealing and injecting glue, it shall be poured evenly along the gap from the end of the gap where glue needs to be injected, so that the glass glue forms a uniform straight line on the surface at the gap, and the excess glass glue shall be scraped off with plastic sheet, And wipe the glue trace with a cloth.

5、玻璃之间对接，玻璃门固定部分因尺寸过大而需要拼接玻璃时，其对接缝要有2-3毫米的宽度，玻璃板边要进行倒角处理。玻璃固定后，将玻璃胶注入对接的缝隙中。注满后用塑料片在玻璃板对接缝的两面将胶刮平，使缝隙形成一条洁净的均匀直线，玻璃面上用干净布擦净胶迹。

5. When the fixed part of the glass door needs to splice glass due to its large size, the butt joint shall have a width of 2-3mm, and the edge of the glass plate shall be chamfered. After fixing the glass, inject the glass glue into the butt joint. After filling, scrape the glue on both sides of the butt joint of the glass plate with a plastic sheet to form a clean and uniform straight line, and wipe the glue trace on the glass surface with a clean cloth.